10 Roller Maintenance Tips

20 May 2020

Making maintenance easy to remember and complete can help ensure your roller runs smoothly all season long.

In today’s work environment, the last thing a contractor wants from their machine is downtime. When a roller breaks down, essential compaction time is lost, affecting density and the entire paving operation.

Keeping your rollers operating at peak efficiency throughout the season can help you better meet both quality specs and deadlines. Here are 10 tips from roller manufacturers that can help ensure your machine runs smoothly all season and without the fear of lost time.

1.      Perform Daily Maintenance Checks

Completing a brief walk-around of the machine can be an easy way to see if something is off before you even leave the shop in the morning.

A daily check of the machine will ensure it's safe. Look for loose wiring and hoses, check for leaks (a sign a hose may be loose), and check the electrical controls. If a switch isn't working, make sure one of the wires isn't loose. Make sure backup alarms, warning beacons and headlights are operating properly and check the center joint and test the parking brake.

2.       Keep the Drum Clean & Lubricated

During your visual inspection each morning, make sure there are no dings in the drum surface and that the drum is clean.

Failure to keep the drum clean or having damage on the surface will result in imperfections in the mat.

3.       Check All Fluid Levels 

From completing the recommended oil change to making sure you have enough coolant, keeping all fluid in check will help ensure the engine at its full performance level. A brief check of the maintenance decal on the machine can also ensure that all fluid is at its optimal level.

4.       Inspect the Water System

You want to make sure everything that has to do with the water system is maintained frequently. If the water system is not working properly, asphalt will start sticking to the drums and no one wants that.

If at all possible, try to always fill the tank with clean water from a known source. Water goes from the tank to the sprinkler bars and sprays out over the front and rear drum. It serves as a lubricant to prevent asphalt from sticking to the drum so it’s important that the water you put in it is clean and won’t clog the system.

If you know you're going to be working in an area where water is scarce, you want to make sure your roller has a water filtering system and that you check it often.

You also want to check the tank regularly for algae, calcium deposits, or other contaminants.

5.       Monitor Drum Scrapers

Keeping drum scrapers well-maintained is a big one and it is an often overlooked maintenance area.

Drum scrapers hold the water to the drum to ensure proper lubrication so if they’re worn, you’re going to lose water between the scraper and the drum and asphalt will start sticking to the edges.

The scraper system needs to be in contact with the drums at all times to spread that water consistently and minimize the potential for asphalt sticking.

When transporting the machine, contractors should also pay close attention to the drum scrapers and make sure they are properly adjusted before starting work. If you’re running that roller for an extended period to get it to the jobsite, you need to make sure they don’t run dry. Either keep water on them or retract the scraper so it doesn’t touch the drum while you’re rolling the machine to the jobsite..

6.       Check Air Filters

Making sure the air filter isn’t clogged can help ensure that the engine won’t run too hot.

A dirty air filter won’t do you any good. If it’s plugged up, you’re generating higher levels of exhaust than you should be.

If the air filter is dirty, you should replace it rather than try to clean it out with compressed. Sometimes you can do more harm than good by trying to clean it.

7.       Hydraulic System      

The hydraulic system is another huge investment in your machine and you need to make sure this system stays maintained.

Checking your hydraulic oil level inside the engine compartment is huge for protecting your investment. Over time, that hydraulic oil needs to be changed but usually you can go 1,000 to 2,000 hours before you need to change it. Always followon the operator’s manual specs. Between maintenance intervals, pay attention to the color of the oil and if it starts looking dark and dingy, it’s time to change it.

8.       Inspect Shock Mounts

The shock mounts are another important part of the roller to check before you leave the shop. The shock mounts are the rubber mounts that isolate the vibration of the drum from the operator.  The energy then is directed from the drum into the mat.

Small cracks in a shock mount are okay, but they can be torn by a truck driver when he ties it down so they need to be checked regularly. If you have a crack where you can stick a quarter in, you should replace that one. If you have a shock mount that is starting to tear or fail, you should replace them all on that side of the drum.

9.       Add Fuel at the End of the Day

Here’s another one that’s easy to do and doesn’t take much effort, but has a big impact on the machine.

By fueling the roller at night instead of the morning, you remove the air from the tank and reduce the likelihood of condensation in the tank. Moisture will add water to your fuel and cause problems.

Plus by filling the tank at the end of each day, you assure greater productivity right away the next morning.

10.   Use the Machine Properly

An asphalt compactor is, for all intensive purposes, designed to shake itself apart. Don’t let your crew be the cause of that any sooner by improperly using the machine.

The easiest maintenance is the maintenance that never has to occur. By properly using the machine you’re not damaging the components unnecessarily.

Proper machine use is also for the benefit of the asphalt mat being laid.

Improper machine use for the application adversely affects the asphalt quality. If you’re using too high of an amplitude or frequency for the job, you might be fracturing the aggregate. When you do that, you’re really changing the design intent and structure of the asphalt.

Over-compaction is the easiest way to damage the machine. You’ve reached density, but you continue to vibrate. Not only are you damaging the asphalt, but all that energy is coming back up in to the machine and you’re prematurely wearing the shock mounts and you could even damage the machine.

While there are times maintenance can fall to the wayside, these tips are here to help you easily remember to protect your investment.

If a machine breaks down, everything comes to a halt unless they have a back-up machine, which is a luxury. We know customers get busy, but those who stay on top of their maintenance will not see as many breakdowns.

Machinery Exchange prides itself in offering great after sales support to all customers and remember you can get all your spare parts from our parts company, Spare Parts Exchange.

Click this link to find out more about Spare Parts Exchange.

 


Back to news

Contact us

Harare Head Office

5 Martin Drive, Msasa
Harare

Telephone

+263 (0)242 447180-2
+263 (0)242 447783-4
+263 (0)732 138067/8

Email

info@machinery-exchange.com

Bulawayo Branch

Cnr 16th Ave / Fife Str Ext, Belmont
Bulawayo

Telephone

+263 (0)29 63191-3
+263 (0)29 63195

Email

info@machinery-exchange.com

Lowveld Branch

34 Lion Drive
Chiredzi

Email

info@machinery-exchange.com

Hwange Branch

632 Baobab Flats
Baobab Hill, Hwange

Email

info@machinery-exchange.com


Midlands Branch

Telephone

08677160798

Email

info@machinery-exchange.com



Machinery Exchange Newsletter

Stay up to date wih the best machinery solutions for Africa.

Make an enquiry